2SC6000 2006-11-13 1 toshiba transistor silicon npn epitaxial type 2SC6000 high speed switching applications dc-dc converter applications ? high dc current gain: h fe = 250 to 400 (i c = 2.5 a) ? low collector-emitter saturation: v ce (sat) = 0.18 v (max) ? high speed switching: t f = 13 ns (typ) absolute maximum ratings (ta = 25c) characteristics symbol rating unit collector-base voltage v cbo 120 v collector-emitter voltage v cex 120 v collector-emitter voltage v ceo 50 v emitter-base voltage v ebo 6 v dc i c 7.0 collector current pulse i cp 10.0 a base current i b 0.5 a collector power dissipation tc = 25c p c 20 w junction temperature t j 150 c storage temperature range t stg ? 55 to 150 c note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant chang e in temperature, etc.) may cause this product to decrease in the reliability significantly ev en if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/derating concept and methods) and indi vidual reliability data (i.e. reliability test report and estimated failure rate, etc). unit: mm jedec D jeita D toshiba 2-7j1a weight: 0.36 g (typ.)
2SC6000 2006-11-13 2 electrical characteristics (ta = 25c) characteristics symbol test condition min typ. max unit collector cut-off current i cbo v cb = 120 v, i e = 0 D D 100 na emitter cut-off current i ebo v eb = 6 v, i c = 0 D D 100 na collector-emitter breakdown voltage v (br) ceo i c = 10 ma, i b = 0 50 D D v h fe (1) v ce = 2 v, i c = 1 ma 160 D D dc current gain h fe (2) v ce = 2 v, i c = 2.5 a 250 D 400 collector emitter saturation voltage v ce (sat) i c = 2.5 a, i b = 83 ma D D 0.18 v base-emitter saturation voltage v be (sat) i c = 2.5 a, i b = 83 ma D D 1.10 v rise time t r D 45 D storage time t stg D 450 D switching time fall time t f see figure 1 circuit diagram v cc ? 20 v, r l = 8.0 i b1 = 83 ma, i b2 = ?166 ma D 13 D ns figure 1 switching time test circuit & timing chart marking ib1 20s ib2 ib1 ib2 input output rl vcc duty cycle 1% c6000 lot no. a line indicates lead (pb)-free package or lead (pb)-free finish. part no. (or abbreviation code)
2SC6000 2006-11-13 3 collector current i c (a) collector-emitter voltage v ce (v) i c ? v ce collector current i c (a) collector current i c (a) v ce (sat) ? i c collector-emitter saturation voltage v ce (sat) (v) collector current i c (a) v be (sat) ? i c base-emitter saturation voltage v be (sat) (v) i c ? v be base-emitter voltage v be (v) 5 10 0 0 6 4 2 1 2 3 4 8 1 0.001 0.001 0.01 0.1 10 0.1 0.01 0.001 10 0.1 0.1 1 0.01 2.0 0.5 0 1.2 1.0 1.5 0.2 0.6 0.8 tc = 100c ? 55 25 0 0.4 1.0 common emitter v ce = 2 v common emitter v ce = 2 v 10 0.001 1000 100 10000 0.01 0.1 1 10 h fe ? i c dc current gain h fe collector current i c (a) common emitter tc = 25 50 30 20 10 5 i b = 2 ma 0 tc = 100c 25 ? 55 common emitter i c /i b = 30 tc = 100c 25 ? 55 1 common emitter i c /i b = 30 tc = ? 55c 100 25 1
2SC6000 2006-11-13 4 r th(j-c) ? t w transient thermal resistance r th(j-c) (c/w) collector-emitter voltage v ce (v) safe operating area collector current i c (a) pulse width t w (s) 10 0.1 0.001 100 0.01 0.1 1 10 1 curves should be applied in thermal limited area. (single non-repetitive pulse) tc = 25 ( infinite heat sink ) 100 1 ms* 10 ms* v ceo max 100 s* 100 ms* i c max (pulse)* 0.1 100 1000 1 0.1 10 0.01 10 s* dc operation tc = 25c *: single non-repetitive pulse tc = 25 c curves must be derated linearly with increase in temperature. i c max (continuous)* 1 10
2SC6000 2006-11-13 5 restrictions on product use 20070701-en ? the information contained herein is subject to change without notice. ? toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity a nd vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba produc ts, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshib a products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconduct or devices,? or ?toshiba semiconductor reliability handbook? etc. ? the toshiba products listed in this document are in tended for usage in general electronics applications (computer, personal equipment, office equipment, measuri ng equipment, industrial robotics, domestic appliances, etc.).these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfuncti on or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage incl ude atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, et c.. unintended usage of toshiba products listed in his document shall be made at the customer?s own risk. ? the products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. ? the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba for any infringement s of patents or other rights of the third parties which may result from its use. no license is granted by implic ation or otherwise under any patents or other rights of toshiba or the third parties. ? please contact your sales representative for product- by-product details in this document regarding rohs compatibility. please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.
|
